this is information on a product in full production. october 2014 docid026687 rev 1 1/9 9 T1610T-8T 16 a logic level triac datasheet ? production data features ? medium current triac ? three quadrants ? ecopack ? 2 compliant component applications ? general purpose ac line load switching ? motor control circuits ? small home appliances ? lighting ? inrush current limiting circuits ? overvoltage crowbar protection description available in through-hole package, the T1610T-8T triac can be used for the on/off or phase angle control function in general purpose ac switching. this device can be directly driven by a microcontroller due to its 10 ma gate current requirement. a2 a1 g a1 a2 a2 g to-220ab table 1. device summary symbol value unit i t(rms) 16 a v drm , v rrm 800 v v dsm , v rsm 900 v i gt 10 ma www.st.com
characteristics T1610T-8T 2/9 docid026687 rev 1 1 characteristics table 2. absolute ratings (limiting values, t j = 25 c unless otherwise stated) symbol parameter value unit i t(rms) on-state rms current (full sine wave) t c = 129 c 16 a i tsm non repetitive surge peak on-state current (full cycle, t j initial = 25 c) f = 50 hz t = 20 ms 120 a f = 60 hz t = 16.7 ms 126 i 2 ti 2 t value for fusing, t j initial = 25 c t p = 10 ms 95 a 2 s v drm , v rrm repetitive surge peak off-state voltage t j = 150 c 600 v t j = 125 c 800 v dsm , v rsm non repetitive surge peak off-state voltage t p = 10 ms 900 v di/dt critical rate of rise of on-state current i g = 2 x i gt , t r 100 ns f = 100 hz 100 a/s i gm peak gate current t p = 20 s t j = 150 c 4 a p g(av) average gate power dissipation t j = 150 c 1 w t stg t j storage junction temperature range operating junction temperature range - 40 to + 150 - 40 to + 150 c t l maximum lead temperature for soldering during 10 s 260 c table 3. electrical characteristics (t j = 25 c, unless otherwise specified) symbol test conditions quadrant value unit i gt v d = 12 v, r l = 30 i - ii - iii min. 0.5 ma max. 10 v gt v d = 12 v, r l = 30 i - ii - iii max. 1.3 v v gd v d = v drm , r l = 3.3 k , t j = 125 c i - ii - iii min. 0.2 v i h (1) 1. for both polarities of a2 referenced to a1 i t = 500 ma max. 15 ma i l i g = 1.2 i gt i - iii max. 20 ma ii 25 dv/dt (1) v d = v r = 536 v, gate open t j = 125 c min. 250 v/s v d = v r = 402 v, gate open t j = 150 c 170 v/s (di/dt)c (1) (dv/dt)c = 0.1 v/s t j = 125 c min. 21.6 a/ms t j = 150 c 15.1 (di/dt)c (1) (dv/dt)c = 10 v/s t j = 125 c min. 11.3 a/ms t j = 150 c 5
docid026687 rev 1 3/9 T1610T-8T characteristics table 4. static characteristics symbol test conditions value unit v t (1) i tm = 22.6 a, t p = 380 s t j = 25 c max. 1.55 v v t0 (1) threshold voltage t j = 150 c max. 0.85 v r d (1) dynamic resistance t j = 150 c max. 27 m i drm i rrm v drm = v rrm = 800 v t j = 25 c max. 7.5 a t j = 125 c 1 ma v drm = v rrm = 600 v t j = 150 c max. 3 1. for both polarities of a2 referenced to a1 table 5. thermal resistance symbol parameter value unit r th(j-c) junction to case (ac) 1.1 c/w r th(j-a) junction to ambient (dc) 60 c/w figure 1. maximum power dissipation versus on-state rms current figure 2. on-state rms current versus case temperature 3 : , 7 5 0 6 $ . ? . 7 f ? & |